In its base
configuration, Model 2004 is a 4 3/4 digit DC voltmeter which
provides exceptionally high resolution, accuracy, and temperature
stability. The standard display range is ±39,999 counts.
Extended-range options are available to ±49,999, ±59,999
or ±69,999 counts. Accuracy is 99.99% of reading. Span tempco
is ±10 to ±20 ppm of reading/°C, made possible
by precision wirewound resistors. The 2004 also features exceptional
noise rejection. Its conversion circuit uses a crystal oscillator,
which is tuned for either 50 or 60 Hz rejection.
BCD OUTPUT STANDARD
Unbuffered, non-isolated parallel BCD output is a standard
feature of the 2004 and is implemented on the main circuit board.
It is good for about 1 ft and can be used to interface the 2004
to a Model 872A comparator or a Model 820A printer. Additional
data and control outputs can be provided by an optional upper-board.
OPTIONS
The meter main assembly can be electrically configured for
four input ranges, four display spans, three round-off modes for
display stability, and high-impedance 3-wire ratio input. Upper-board
options include four BCD output boards and a single-setpoint controller.
Mechanical options for the standard 1/8 DIN case include a screw-terminal
barrier strip for signal and power and a splash-proof lens cover
which meets NEMA-4 requirements. A NEMA-size case is optional.
LA1
(Ultra-Low)
Load-Cell Conditioner Upper Board
LP1
(Ultra-Low)
Load-Cell
Peak-Hold Upper Board
OPTION
F3A
Non-Isolated Parallel BCD Upper Board, Three-State
with 1-Bit Enable
OPTION F3P
Peak/Valley Detector Upper Board with BCD Output
OPTION F4A
Isolated Parallel BCD Upper Board, Three-State
with 1-Bit Enable
OPTION F4M
Isolated, Parallel BCD Upper Board Three-State
with 4-Bit Address
OPTION 06
Digital-Setpoint Upper Board
OPTION SPC4
1/8
DIN NEMA-4 Splash-Proof Lens Cover
SPECIFICATIONS
ANALOG
INPUT
Standard
Range
|
±399.99
mV
|
±3.9999
V
|
±39.999
V
|
±399.99
V
|
Resolution
|
10
µV
|
100
µV
|
1
mV
|
10
mV
|
Maximum
Input
|
100
Vp
|
100
Vp
|
250
Vp
|
250
Vp
|
Input
Resistance
|
1
Gohm
|
1
Gohm
|
1.1
Mohm
|
1.0
Mohm
|
Bias
Current
|
2
nA
|
2
nA
|
200
pA
|
20
pA
|
Span
tempco/°C
|
±15
ppm
|
±10
ppm
|
±20
ppm
|
±20
ppm
|
Configuration: Bipolar, single-ended
Zero: Automatic
Span adjustment: ±1.2%
NOISE REJECTION
NMR: 70 dB, 50/60 Hz
CMR: 120 dB, DC to 60 Hz
CMV: 1500 Vp per HV test, 354 Vp per IEC spacing
ACCURACY AT 25°C
Maximum
error: ±0.005% of reading ±2 counts ±10 µV
Span tempco: ±10 to ±20 ppm/°C
Step Response: 1 s
Warmup to rated accuracy: 1 hour
ANALOG-TO-DIGITAL CONVERSION
Technique: Dual-slope, average-value
Polarity: Automatic
Signal integration period: 33 ms at 60 Hz, 40 ms at 50 Hz
Read rate: 3.3/s at 60 Hz, 2.8/s at 50 Hz
3-WIRE
RATIO REFERENCE
Analog
input range
|
±400
mV
|
±4,
±40, ±400 V
|
Reference
Voltage
|
+0.1
to +0.4 V
|
+1.0
to +4.0 V
|
Load
on reference, std
|
260
ohm
|
2.6 kohm
|
Load
on reference, opt
|
1
Gohm
|
1
Gohm
|
Accuracy
|
99.95%
|
99.95%
|
DISPLAY
Type: 7-segment, red LED
Height: 0.56 in (14.2 mm)
Symbols: 8.8.8.8.8
Decimal points: Four positions programmable internally or
at connector
Overrange indication: Display flashes
DIGITAL
SIGNALS
Output
signals: TTL-compatible
Input signals: TTL or 5 V CMOS compatible
POWER
AC voltages: 115 V ac ±10% at 60 Hz; 230 V ac ±10%
at 50 Hz
DC voltage: 5 V dc ±5%
Power consumption: 4.5 W (nominal)
ENVIRONMENTAL
Operating temperature: 0 to 50°C
Storage temperature: 40 to 75°C
Relative humidity: 95% at 40°C (non-condensing)
MECHANICAL
Dimensions: Newport DIN1A (1/8 DIN) case standard, Newport
NEMA-size case optional (see Mechanical section for drawings)
Weight: 17 oz (480 g)
Case material: 94V-0 UL-rated polycarbonate
|
|
† All dollar amounts on this site are shown in US currency.
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
Part Number Builder |
 |
 |
 |
 |
 |
 |
|
Option Descriptions
|
(1)
|
INPUT SIGNAL
|
|
Select -AVG for AC voltage (includes D4) -RMS for True RMS voltage (includes D4) -LA1 for Gain-programmable preamplifier with active filter and bridge-excitation supply -LP1 for Gain-programmable preamplifier with peak-hold and bridge-excitation supply - DC Input Signals -2 for ± 399.99 mVdc -3 for ± 3.9999 Vdc -4 for ± 39.999 Vdc -5 for ± 399.99 Vdc
(2)
|
DC INPUT SIGNALS (Not applicable for LA1, LP1, or FS Input Signals)
|
|
Select Nothing(leave field blank) for Not applicable ,VR2 for 399.99 mVac or rms ,VR3 for 3.9999 Vac or rms ,VR4 for 39.999 Vac or rms ,VR5 for 399.99 Vac or rms ,CR2 for 399.99 µA ac or rms ,CR3 for 3.9999 mAac or rms ,CR4 for 39.999 mAac or rms ,CR5 for 399.99 mAac or rms ,CR6 for 3.9999 A ac or rms ,CR7 for Current transformer (CT) scaling for 5 A ac or rms
(3)
|
EXTENDED RANGE OPTIONS
|
|
Select Nothing(leave field blank) for None, ±39,999 counts (standard) ,ER1 for ±49,999 counts (DC or FS signal only) ,ER2 for ±59,999 counts (mutually exclusive with FS option) ,ER3 for ±69,999 counts (mutually exclusive with FS option)
(4)
|
LEAST-SIGNIFICANT-DIGIT ROUND-OFF
|
|
Select Nothing(leave field blank) for Displays 0,1,2,3,4,5,6,7,8,9 ,CB2 for Displays 0,2,4,6,8 ,CB5 for Displays 0,5
(5)
|
3-WIRE RATIO DC INPUT IMPEDANCE
|
|
Select Nothing(leave field blank) for Standard ,HZ for High impedance (1 G ohm reference input only)
(6)
|
UPPER-BOARD OUTPUT OPTIONS - Mutually exclusive with LA1 and LP1 - *Includes PCB edge card connectors
|
|
Select Nothing(leave field blank) for None (unbuffered, non-isolated BCD is standard)* ,F3A for Buffered, gated and stored BCD output* ,F3P for Stored peak or valley BCD output* ,F4A for Buffered, isolated, gated and stored BCD output* ,F4M for F4A with 4-line binary addressing* ,06 for Single-setpoint controller with TTL and 1A relay outputs (requires option D4)*
(7)
|
POWER
|
|
Select Nothing(leave field blank) for 120 Vac (optimized for 60 Hz rejection) ,C1 for 240 Vac (optimized for 50 Hz rejection) ,C3 for 5 Vdc (optimized for 60 Hz rejection** ,C4 for 5 Vdc (optimized for 50 Hz rejection)**
(8)
|
ADD-ON OPTIONS
|
|
Select Nothing(leave field blank) for No Options ,FS1 for Custom calibration for 2004-AVG-CR7 or 2004-RMS-CR7
(9)
|
ADD-ON OPTIONS
|
|
Select Nothing(leave field blank) for No Options ,D4 for Screw-terminal barrier strip for power and signal. Removes power and signal from D1
(10)
|
ADD-ON OPTIONS
|
|
Select Nothing(leave field blank) for No Options ,BL for Lens without Newport logo
|
NOTE: All combinations may not be valid, check spec sheet for valid part numbers. |
| | | | | | | | |
|
 |
 |
|
|
|
Keywords: 4 3/4 Digit DC Voltmeter with BCD Output
|
Back to top |
| |