Navigation image map
Contact Us Distributor Site Map Manuals Home Products

Wireless Process Transmitter for Sensors with Voltage or Current Output

Wireless Process Transmitter for Sensors with Voltage or Current Output
Convert Process Signal to Wireless
Accepts 0 to 1V, 0 to 5V, 0 to 10V and 4 to 20 mA Signals
Industrial NEMA 4X (IP65) Enclosure
Free Software for Monitoring, Recording, and Data Logging Included
Low Power Operation/Sleep Mode for Long Battery Life
UWTC Receivers Work with Up to 48 Wireless Transmitters

1 Year Warranty New Electromagnetic Compatibility

Scroll Below to Order Specs Manuals

The new UWPC wireless process transmitter converts standard process signals (0 to 1V, 0 to 5V, 0 to 10V and 4 to 20 mA) into a wireless signal that can be transmitted up to 120 m (400'), eliminating the need for wiring runs in a variety of environments. The wireless transmitter is housed in a NEMA 4X (IP65) enclosure, providing water and dust protection. The UWPC transmits data at preset intervals, selectable from 2 to 120 seconds. Transmitted data includes the sensor reading, along with RF signal strength and battery status.

The UWPC is compatible with the UWTC-REC family of wireless receivers, which can accept signals from up to 48 wireless transmitters, and display them on a PC. Receivers are available with optional display and analog output. An analog output can be used to interface with a process controller, PLC or data acquisition device. Each unit includes free software that converts your PC into a monitor, chart recorder or data logger. Readings can be saved and later printed or exported to a spreadsheet file.

Wireless Receivers
UWTC-REC1: 48-channel wireless receiver with USB
UWTC-REC2: 48-channel wireless receiver with USB and single analog output
UWTC-REC4: 48-channel DIN rail mount wireless receiver with USB and four analog output signals
UWTC-REC6: economical single channel wireless receiver with single analog output

Input Range: 0 to 1 Vdc, 0 to 5 Vdc, 0 to 10 Vdc or 4 to 20 mA
Accuracy: ±0.04% of range
Input Connection: Panel connector (mating connector supplied)
Computer Interface: USB, for initial transmitter/sensor setup and configuration
Transmit Sample Rate: Programmable from 1 sample/2 sec to 1 sample/120 sec
Radio Frequency (RF) Transceiver Carrier: ISM 2.4 GHz, direct sequence spread spectrum
RF Output Power: 10 dBm (10 mW)
Range of RF Link:
  Outdoor Line of Sight: Up to 120 m (400')
  Indoor/urban: Up to 40 m (130')
RF Data Packet Standard: IEEE 802.15.4, open communication architecture
Software (Included Free): Requires Windows® 2000, XP or Vista (32 bit) operating system
Power: One 3.6V, lithium "C" cell (included)
Battery Life (Typical): 3 years 1 sample/minute reading rate @ 25°C
Enclosure: NEMA 4 (IP65), polycarbonate
Enclosure Dimensions: 80 L x 82 mm W (3.15 x 3.23")
Weight: 272 g (9.6 oz)

Product Selection (Specify Model Number)
 Part Number   Availability   Price    Description   
 UWPC-2-NEMA 2 Weeks    $346.50     Wireless process input transmitter, 0 to 1 Vdc, 0 to 5 Vdc, 0 to 10 Vdc or 4 to 20 mA input ranges  
 UWTC-CABLE in-stock    $10.92     Spare USB programming/communication cable  
 UWTC-BATT-C in-stock    $52.00     Replacement 3.6V, lithium "C" cell battery assembly  
All dollar amounts on this site are shown in US currency.

 Note: Because of transmission frequency regulations, these products may only be used in the United States, Canada, Europe and China (please note CE compliance of the specific model for use in Europe).
Comes complete with measurement/data logging software, lithium "C" cell battery, USB cable, and operator's manual.
 Ordering Example: (1) UWPC-2-NEMA wireless process input transmitter, (1) UWTC-REC1 48-channel wireless receiver, with USB communications = $619.5

Keywords: Wireless Process Transmitter for Sensors with Voltage or Current Output

   Back to top